Nameplate vs duty cycle vs rated label vs household average: which appliance energy estimate should you use?
Use your model’s rated annual kWh (EnergyGuide or ENERGY STAR) when you know it: it is measured under a standard DOE test. Without it, the household survey average (EIA RECS 2020) is the most realistic typical figure. Nameplate watts are the maximum draw (DOE), so watts × hours is an upper bound except for appliances that draw full power whenever they are on.
Playground: every method on your numbers
Best answer
Annual cost$111.36/yr
Low $111.36/yr · likely $111.36/yr · high $111.36/yr
No input here carries a documented range, so no range is shown.
Annual energy
617.3 kWh/yr
Formula Showdown
Method
Result
When it is right
Nameplate watts × hours
needs watts
Appliances that draw close to their rated power the whole time they are on (kettle, toaster, hair dryer, bulbs, a heater without a thermostat). Bias: The nameplate wattage is the maximum power drawn (DOE), so this overestimates appliances that cycle or vary their power (refrigerators, thermostat-controlled heaters and air conditioners).
Watts × duty cycle
needs watts
Appliances that switch on and off to hold a temperature, when you know (or DOE gives) the share of time they actually run. DOE: a refrigerator runs at full power about one third of the time it is plugged in. Bias: The real duty cycle depends on room temperature, settings and use; DOE’s one-third is a rule of thumb for refrigerators only.
Rated annual kWh (EnergyGuide / ENERGY STAR)
needs ratedAnnualKwh
Whenever the appliance has a rated annual energy figure (EnergyGuide label or ENERGY STAR listing), especially for refrigerators, freezers and cycle-based appliances. Bias: The rating is measured under standard test conditions and typical use; your kitchen temperature, settings and usage can differ. Use the usage factor to scale it.
Household survey average (EIA RECS 2020)Recommended
$111.36/yr
When you do not know your model’s rating: what US households that have this appliance use on average (typical use, typical age of appliance). Bias: An average over all households and appliance ages; your use, climate and model can differ a lot. Older appliances in homes often use more than a new rated model.
Why this one: Without your model's rating, the measured average for US households is the most realistic typical figure; nameplate watts are only the maximum draw.
Solve for any input
Show the work
Energy per year: Average annual use among US households that have this appliance (RECS 2020) E_yr = 617.3 kWh/yr = 617.3 kWh/yr[1]
Annual cost: Annual energy × price per kWh C_yr = 617.3 kWh/yr × $0.18/kWh = $111.36/yr[?] Load profile for refrigerator: continuous cycling (DOE test procedure assumes the compressor runs 50% of the time; U.S. Department of Energy).
Copy this code. The visible credit link must stay.
<iframe src="https://thebestcalculator.com/embed/cost-to-run/" title="Appliance running cost" width="100%" height="720" loading="lazy"></iframe>
<p><a href="https://thebestcalculator.com/">Calculator by The Best Calculator</a></p>
Where the methods disagree (real data)
For each appliance, the average use in US homes that have one (RECS 2020) against the rated energy of a typical new ENERGY STAR certified model. Washers and dishwashers are left out: their ratings include water heating, the survey figure does not.
Blue: household average (RECS 2020). Grey: typical certified model (ENERGY STAR median rating).
The household average covers every age of appliance in real homes; the rating is a standard test of a new model. A large gap means a new efficient model, or a different usage pattern, changes the answer a lot.
The four methods
Nameplate watts × hours
E_yr = W × h × D ÷ 1000
Right when: Appliances that draw close to their rated power the whole time they are on (kettle, toaster, hair dryer, bulbs, a heater without a thermostat).
Known bias: The nameplate wattage is the maximum power drawn (DOE), so this overestimates appliances that cycle or vary their power (refrigerators, thermostat-controlled heaters and air conditioners).
Right when: Appliances that switch on and off to hold a temperature, when you know (or DOE gives) the share of time they actually run. DOE: a refrigerator runs at full power about one third of the time it is plugged in.
Known bias: The real duty cycle depends on room temperature, settings and use; DOE’s one-third is a rule of thumb for refrigerators only.
Right when: Whenever the appliance has a rated annual energy figure (EnergyGuide label or ENERGY STAR listing), especially for refrigerators, freezers and cycle-based appliances.
Known bias: The rating is measured under standard test conditions and typical use; your kitchen temperature, settings and usage can differ. Use the usage factor to scale it.
Right when: When you do not know your model’s rating: what US households that have this appliance use on average (typical use, typical age of appliance).
Known bias: An average over all households and appliance ages; your use, climate and model can differ a lot. Older appliances in homes often use more than a new rated model.
Recommendation rules (the same ones the calculator uses)
A rated annual kWh exists → use it (measured under a standard DOE test procedure).
The appliance draws full power whenever it is on and you know its watts and hours → nameplate watts × hours.
Otherwise, for typical use → the household survey average (RECS 2020).
Cycling appliances with a known duty cycle → watts × duty cycle.
Only nameplate data → treat watts × hours as an upper bound.
Why they differ
Nameplate watts are the maximum power drawn (DOE Energy Saver), not the average.
Appliances that cycle (refrigerators, freezers, air conditioners) run only part of the time; DOE’s refrigerator test assumes the compressor runs 50% of the time (10 CFR 430 Subpart B, Appendix A).
Ratings describe a new model under test conditions; homes contain older appliances used in different ways.
Limits
US data only for the household averages and certified-model ratings. Standby power is not counted unless the rating includes it. Figures are estimates, not a measurement of your appliance: a plug-in energy meter measures it directly.
Data: EIA RECS 2020 (microdata v7); ENERGY STAR certified products (snapshot 2026-11-20). Engine method versions: energy.appliance_running_cost@1.0.0. By The Best Calculator (review pending). Changelog.